We may earn commission from links on this page at no extra cost to you. We only recommend products we back!
If you’re trying to figure out the casting number on your cylinder head, there are a few ways you can go about it. You can either check the number stamped on the side of the head, or you can look it up in a parts catalogue.
If you can’t find the casting number on the head, you can also check the engine block. The casting number will be located on the side of the block, near the bottom.
How do I find my head casting number?
There are a few ways to find your head casting number.
How do you identify an engine or cylinder head?
There are a few ways to identify an engine or cylinder head. One way is to look for markings on the engine itself. Another way is to look up the engine’s serial number in a database.
Where are the casting numbers on Ford FE heads?
The casting numbers on Ford FE heads can be found on the top of the engine, near the front.
How can you tell if a cylinder head is a world product?
There is no definitive answer to this question, as there are no specific markings or features that all world cylinder heads share. However, there are a few ways to tell if a cylinder head is likely to be a world product:
What motor did 823 heads come on?
The 823 heads were used on the following motors: 327, 350, and 400.
What heads came on 6.0 LS?
The 6.0 LS came with a few different heads, depending on the model year and specific engine. The most common heads were the LQ4 and LQ9, although the L76 and LS2 were also options in some cases. The heads are all cast iron, with either 64 or 72cc combustion chambers. The LQ4 had a smaller camshaft and less aggressive porting, while the LQ9 had a more aggressive camshaft and porting. The L76 and LS2 were similar to the LQ9, but with even more aggressive camshafts and porting.
What are 882 Chevy heads?
The 882 Chevy heads are a set of performance cylinder heads designed for use on Chevrolet small-block engines. They were introduced in 1986 as a replacement for the factory heads that were prone to cracking, and they quickly gained popularity among racers and street performance enthusiasts. The 882 heads feature larger intake and exhaust ports than the factory heads, as well as a higher compression ratio. They are also capable of supporting larger camshafts and valves than the factory heads.
How do I identify 350 Vortec heads?
There are a few ways to identify 350 Vortec heads. One way is to look for the words “Vortec” and “350” cast into the heads. Another way is to measure the combustion chamber volume; Vortec heads have a volume of 56cc. Additionally, the exhaust ports on Vortec heads are rectangular, and the intake ports are oval.
Are 882 heads any good?
This is a difficult question to answer without knowing more about the specific 882 heads in question. Generally speaking, 882 heads are considered to be good performance heads for small-block Chevy engines. They flow well and are often used in racing applications. However, it is always best to consult with a qualified engine builder or mechanic to get specific advice for your particular engine.
Where are the casting numbers on a Ford engine?
The casting numbers on a Ford engine are located on the engine block, cylinder heads, intake manifold, and oil pan.
How do you identify Fe heads?
To identify Fe heads, you can look for the following characteristics:
How do you read a Ford engine number?
The Ford engine number is located on the engine block, usually on the left-hand side. It is a seven-digit number, typically starting with the letters “F” or “P.”
How do I identify a Ford cylinder head?
There are a few ways to identify a Ford cylinder head. One way is to look for the Ford logo cast into the side of the head. Another way is to look for the word “Ford” stamped into the side of the head.
What is the difference between 821 and 823 heads?
The 821 head was used on 1967 and 1968 model year 400 cid engines. The 823 head was used on 1969 and 1970 model year 400 cid engines. The main difference between the two heads is the exhaust port configuration. The 821 head has smaller exhaust ports and is not compatible with the 1969 and newer exhaust manifolds. The 823 head has larger exhaust ports and is compatible with the 1969 and newer exhaust manifolds.
Which heads are better 706 vs 862?
There is no definitive answer to this question as it depends on a number of factors, including the specific application for which the heads are being used, the engine displacement, the camshaft profile, the intake and exhaust system, and the tuning. In general, the 862 heads will flow more air and provide more power than the 706 heads, but the 706 heads may provide better fuel economy and low-end torque.
What heads came on 4.8 LS?
The 4.8 LS came with the following heads:
What did 862 LS heads come on?
862 LS heads came on the following:
How do I know if I have LQ4 or LQ9?
The easiest way to tell the difference between an LQ4 and LQ9 engine is by the cylinder heads. LQ4 heads have cast-iron construction with six bolt holes per cylinder, while LQ9 heads are made from aluminum and have eight bolt holes per cylinder. Another way to tell them apart is by the intake manifold. LQ4 engines have a plastic intake manifold, while LQ9s have an aluminum intake manifold.
What casting number are LS3 heads?
The casting number on LS3 heads is 862.
Where are the casting numbers on a Chevy head?
The casting numbers on a Chevy head can be found on the front of the engine block, on the side of the cylinder head, or on the rocker arm cover.